Hey Big Mookied

Post your Binder related Tech here.

Moderators: Toyman1994, TallGuy, Tice, Ashman

Hey Big Mookied

Unread postby BornReadyBinder » Wed May 13, 2009 7:56 am

You know, if you didnt spend so much time making hooch....you could be ready for the Frisco. Or are you ready to go? :D
















:flipoff: :D

That is all.
Last edited by BornReadyBinder on Wed May 13, 2009 7:57 am, edited 1 time in total.
User avatar
BornReadyBinder
Supporting Member
Supporting Member
 
Posts: 1276
Joined: Sat Jun 18, 2005 2:56 am
Location: Safford, AZ

Unread postby BornReadyBinder » Wed May 13, 2009 7:56 am

At least share your recipe. :D
User avatar
BornReadyBinder
Supporting Member
Supporting Member
 
Posts: 1276
Joined: Sat Jun 18, 2005 2:56 am
Location: Safford, AZ

Unread postby bigmookied » Wed May 13, 2009 10:07 am

haha!!

If I can ever be home I can get my junk ready, but now I am way far behind and leaving again.

Looks like I am going to have to sit this one out, Sucks the big one!!

As for the brew, try Brew your own Beer and Wine in Tuscon http://www.brewyourownbrew.com

Just bought a bucket, airlock and the brew kit to start. Ordered a keg and had an old CO2 bottle laying around.

I spend too much on good beer, time to make my own and save money this year....
"The Beast/Mule" - 1969 IH Travelall 3/4 Ton 4X4, 345, EB 1405, MSD 6Al, D60 Rear, D44 front. 37" Mils and 24 Bolt wheels. Copper Metallic glory, now too pretty to wheel hard. Looks like I need a Scout to link and wheel now!!!
User avatar
bigmookied
WAZ Vendor
WAZ Vendor
 
Posts: 87
Joined: Mon Aug 04, 2008 9:44 pm
Location: San Tan Valley, AZ

Unread postby BornReadyBinder » Wed May 13, 2009 1:37 pm

Did you get the trans fixed?
User avatar
BornReadyBinder
Supporting Member
Supporting Member
 
Posts: 1276
Joined: Sat Jun 18, 2005 2:56 am
Location: Safford, AZ

Unread postby bigmookied » Thu May 14, 2009 6:30 am

I replaced some seals, pan gasket, cleaned and painted (for leak detection mainly) and it is sitting on a jack underneath the Travelall. Needs to move about 24" higher and get bolted in.

Plus I have a replacement I got from Russ sitting in there too. I think that one leaks worse then mine ever did just sitting, seems to have dumped 2 quarts without moving. At least mine had to move to start leaking.
"The Beast/Mule" - 1969 IH Travelall 3/4 Ton 4X4, 345, EB 1405, MSD 6Al, D60 Rear, D44 front. 37" Mils and 24 Bolt wheels. Copper Metallic glory, now too pretty to wheel hard. Looks like I need a Scout to link and wheel now!!!
User avatar
bigmookied
WAZ Vendor
WAZ Vendor
 
Posts: 87
Joined: Mon Aug 04, 2008 9:44 pm
Location: San Tan Valley, AZ


Return to Binder Tech

Who is online

Users browsing this forum: No registered users and 1 guest

cron